no havent thought about how im gonna do that yet, any ideas?

r the cells in my cad to big cause to me they look a bit
EDITED: i just answered my own question way to big

new cad update, if you notice there r alot more batteries cause i actually look at my battery packs and counted how many cells, and i was bored so i stuck in some textures

how will the pulley on the motor attach it doesnt even extend out past the bolt holes.
_________________
www.demon50s.com - Minimoto parts
http://www.youtube.com/user/HyzerGlen - Videoooozzz

ah i see wat u mean, does that part of a fan motor spin aswell, i havent used well never actually seen a fan motor before.

that specific type does it has a spinning plate.
_________________
www.demon50s.com - Minimoto parts
http://www.youtube.com/user/HyzerGlen - Videoooozzz

hows that

This is how the motor looks with a 4" pulley:






You can't see the flange but the 3 screws in the face of the pulley screw into it. if you pulley doesn't cover the existing holes, you will need to drill & tap some new ones closer to the stub axle
_________________
Australian 2015 Featherweight champion
UK 2016 Gladiator champion

ok i still gotta go get some pulleys and that motor only problem is i live to far away to go to that PnP place, on the weekend im gonna go have a look at a wreckers might beable to pick one up, wat is the brand of the motor

I think you will have a weight problem if you use that weapon setup and steel armour. My first version of Jolt was quite a similar layout and with a slightly heavier motor, the same drive motors and about the same batteries, it came right up to the weight limit. at that time, Jolt had a 5mm aluminium welded frame with no top armour, which would be far lighter than the frame in your CAD. based on that, you will need to lighten up the frame heaps...
_________________
Australian 2015 Featherweight champion
UK 2016 Gladiator champion

yeh well im gonna have to wait till i know wat type of metals i can get when i know that i will see wat i can do may make the top of the shell not as thick as the rest i dont know ill have to wait and see

Ok time to start to think about building this im still open for ideas but hears wat i have come up with: armour still undecided, weapon bar will most likely be 2 to 3cm steel bar about 40cm long, still looking for some ali blocks for the bearing blocks dont know how im gonna make them, pulleys well i cant find any help with that would be good, gonna go looking for a 20mm steel rod for the shaft, weapon motor well dont have one was wondering if someone could pick me up a nichi ra fan motor next time they r at pnp that would be good, other then that i have everything else if there is anything else that i have missed and if anyone has any ideas that could help me out it would be appreciated
_________________
Barton Robotics Youtube Channel:
https://www.youtube.com/user/dyl30

Barton Robotics Facebook Page:
https://www.facebook.com/BartonRobotics

Google "stenco pulley", you will find they are made locally and many suppliers have them - not too sure about your area though.
_________________
Australian 2015 Featherweight champion
UK 2016 Gladiator champion

you can always scab some cast pulleys from a car (water pump drive belt or something like that) they usually arent too big. most places have wreckers.

for visceral it just uses two 20mm plastic blocks with holes spade bitted out then dremeled to size with the bushes forced in. totally didnt work that well lol but its as cheap as youll get on that front.
_________________
www.demon50s.com - Minimoto parts
http://www.youtube.com/user/HyzerGlen - Videoooozzz

I had a look and there is a pulley shop near where i live im gonna have to go check that places out hopefully they have some stenco pulleys how can i attach the pulley and weapon bar to the shaft well wat would be the easiest and strongest method
_________________
Barton Robotics Youtube Channel:
https://www.youtube.com/user/dyl30

Barton Robotics Facebook Page:
https://www.facebook.com/BartonRobotics