hey im just wondering what would happen if i hooked up a 27mhz & 40mhz transmitters up to the same arial or recievers up to the same arial e.g interferance ect???
_________________
WHEN YOU GO TO COURT YOU'RE TRUSTING YOUR FATE TO TWELVE PEOPLE
WHO AREN'T SMART ENOUGH TO GET OUT OF JURY DUTY

Hmm looks like your trying what i did once, hacking two rc toys for a weapon and drive... trust me, it won't survive ONE match unless you got some decent rc toys. I'm not sure about interference, wouldn't think so.
_________________
( •_•)

( •_•)>⌐■-■

(⌐■_■)

YEAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAH

it dosent matter about the quality, i'm just using the tx/rx but i'm making those little relay/diode speed controllers i told u about
_________________
WHEN YOU GO TO COURT YOU'RE TRUSTING YOUR FATE TO TWELVE PEOPLE
WHO AREN'T SMART ENOUGH TO GET OUT OF JURY DUTY

it probably wont work unless you have the same crystals in there. i ran 29mhz tx and 36mhz rx in kang. didnt work too well. got a few matches out of it.

i wouldnt even attempt the two txs on the same aerial. two aerials of appropriate length for each.
_________________
www.demon50s.com - Minimoto parts
http://www.youtube.com/user/HyzerGlen - Videoooozzz

no i mean a 40 mhz tx/rx for drive and 27 mhz weapon and both tx to the same arial and both rx to the same arial by the way its 2 cheap rc cars that i'm turning into an ant
_________________
WHEN YOU GO TO COURT YOU'RE TRUSTING YOUR FATE TO TWELVE PEOPLE
WHO AREN'T SMART ENOUGH TO GET OUT OF JURY DUTY

Just use two for simplicities sake, not like they weigh much. . .
_________________
Jeff Ferrara
fb@ffej.net

ffej.net

i know it would be simple but i want it to look 1st class
_________________
WHEN YOU GO TO COURT YOU'RE TRUSTING YOUR FATE TO TWELVE PEOPLE
WHO AREN'T SMART ENOUGH TO GET OUT OF JURY DUTY

Just use two, would look fine if you did it right.
_________________
( •_•)

( •_•)>⌐■-■

(⌐■_■)

YEAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAH

hey i got a little rc car it runs on 3v (2 aaa's) and i got a battery out of one of thse cheap knock-of dremels and its 3.5v but over 20 amps and i was wondering if it would fry my circits
_________________
WHEN YOU GO TO COURT YOU'RE TRUSTING YOUR FATE TO TWELVE PEOPLE
WHO AREN'T SMART ENOUGH TO GET OUT OF JURY DUTY

Last edited by wilko on Fri Feb 24, 2006 4:57 pm; edited 1 time in total

Most cheap rc circuits could probably handle that, mainly due to a safety margin in the components.. i've run a microCharge circuit board at 9v for a little while... heated up bigtime but it didn't fry (probably was about to though, don't recommend it!... )
_________________
( •_•)

( •_•)>⌐■-■

(⌐■_■)

YEAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAH

i'm worried about the amount of amps coming out of the battery
_________________
WHEN YOU GO TO COURT YOU'RE TRUSTING YOUR FATE TO TWELVE PEOPLE
WHO AREN'T SMART ENOUGH TO GET OUT OF JURY DUTY

There is an amp hour rating for a battery. It is a measure of the power of the battery. The current of a circuit is the voltage of the cicuit divided by the resistance of the circuit. You will not change the current draw of a cicuit by using a higher amp hour battery.
_________________
So even the rain that falls isn't actually going to fill our dams and our river systems

i got the rc car for my ant (its not really an ant more a sozbot)but any way it works quite well
i also bought a remote controlled excavator off ebay for 99c (+ $19 postage ) and i'm turning it into a sozbot as well so if any one wants to vs me let me know
_________________
WHEN YOU GO TO COURT YOU'RE TRUSTING YOUR FATE TO TWELVE PEOPLE
WHO AREN'T SMART ENOUGH TO GET OUT OF JURY DUTY

LOL sucky, where in NSW is ballina? The competition is in blacktown if you want to come down... I'll verse ya eh eh
_________________
( •_•)

( •_•)>⌐■-■

(⌐■_■)

YEAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAH

Ballina is about 2 hours south of Brisbane!

So about 8 or 9 hours from Blacktown !